• Big three stage filtration

• High volume airflow

• Inside foam can be checked for dirt penetration, helps to know when to clean filter

• More airflow than the old filter

• One filter for on-road and off-road

• Run longer between cleaning

• Stops dirt even better than before

• Quick change bases for different angles and sizes

• New 60°  elbow for T-maxx with Pro .15 engine, fits under body

• New 60°  elbow for T-maxx & Revo 2.5R / 3.3 engines, fits under body

• Base stays on tighter

• Lighter weight

1. 90° off-road filter designed for high h.p. big block engines
2. Highest airflow possible
3. The most dirt stopping power filter we have ever made
4. Inside foam can be removed for quick check of dirt penetration

1. With 60° base filter can go parallel to the chassis for ram effect
2. Superior strength is put into 90° and 60° bases to help keep filters from falling off
3. Screen filter is curved slightly out to hold outside foam element in position
4. 90° and 60° filters are built with extra light materials keeping weight down

1. The high airflow filter is balanced perfectly for the 2.5R / 3.3 engine.  It has ram air capability for mid and top end.
2. Very fine powdery dirt is a harsh environment for nitro engines.  The filter cap can be removed to slide out the inner foam.  Dirt ring will show at the end of the foam element.  This will help give information when it is time to clean.
3. This filter with a 60° base is parallel with the chassis and clears the transmission and linkage.  There is also room to add the1/8 scale outer foam element .

• Holds as good or better than tie-straps
• Easier to install in tight and hard to reach places
• Fits Traxxas 2.5R / 3.3 Tmaxx, Revo and Jato
• Fits HPI Savage 21, 25 
• Fits most 16mm carburetors
• Unclamps to remove filter from carburetor

This filter with a 15mm base is used on  .12 on-road and off-road engines that have big slide carbs.  Airflow and dirt filtration work especially well for this size 1/10 scale engine.

• For 15mm and 16mm carburetors
• High grade materials
• Comes three in a pack
• Fits sound box

Part Number 10ST

Part Number 11ST

1. This filter has more airflow and dirt stopping power than our old filter.

2. New cap and screen filter design hold a large one-piece foam element maximizing the filter to fit in tight spaces.

Part Number 1045

Part Number 1145

1. This filter has a 45° base.  Air flows better over top of filter and front of engine for more cooling.

2. Filter base can be changed to fit large and small carbs.  Base kits come with a straight, 45° and 60° base and are available in 10mm and 11mm sizes.

Part Number 1060

1. This filter fits under the  T-maxx body on the Pro.15 engine.  The 60° fits 10mm and 11mm carbs.

2. This filter has higher airflow and longer run time between cleaning than our older filter.

3. Super duty can can be used with this 60° long base with no restriction to spur gear and transmission.

Part Number S1045

Part Number S1145

1. 45° base with super duty cap does not affect idle of engine, low or no restriction of air.

2. There are new high h.p. and high rpm engines coming out all the time.  The new filter design balances power with engine protection.

Part Number S1060

1. Fits T-maxx with Pro.15 engine.  Super duty cap "looks cool".

2. Super duty cap helps deflect mud, dirt and rain from going directly in to the filter.  The super duty cap also has a little bit of noise reduction.

Part Number BS10

Part Number BS11

10mm Base Kit with one each 60°, 45° and Straight Base   P/N: BS10

11mm Base Kit with one each 60°, 45° and Straight Base   P/N: BS11

Part Number 10FM

See pictures on "More Information" page.

• Extra gripping power
• Cap won't come off even with high impact and rollovers